REVIT Crater Gloves :: MotorcycleGear.com

REVIT Crater Windstopper Gloves

PROTECTION FEATURES
Outer shell
  • WINDSTOPPER® Soft Shell 3L stretch
  • Connect finger tip fabric
  • PWR Oxford
  • Flock PU
  • Goatskin drum dyed
Lining
  • Polar fleece liner
  • Tri-fleece liner
Protection
  • Temperfoam®
  • WINDSTOPPER® Soft Shell 3L stretch covered hard-shell knuckle
  • PWR shield knit
Visibility
  • Laminated reflection
Composition
  • 42% Leather, 27% Polyamide, 26% Polyester, 3% Polyurethane, 2% EPTFE
ERGONOMIC FEATURES
Fit
  • City fit
Adjustability
  • Adjustment strap
Features
  • Visor wipe
  • Connect finger tip
  • Knitted cuff

Please Note: We can ship REV’IT! products to US, US territory or APO/FPO addresses only (per manufacturer’s restrictions).

Tweet_button Share this page on Twitter!

Free Shipping on All Orders over $89!
MSRP:
$99.99
,  Our Price:
$72.00

Sizing Information

Most REV’IT! gloves feel a bit snug as compared to other American brands we carry and these are no exception. I’d say this one runs only slightly small, so I’d advise you to choose the size you normally wear in gloves. If you are between sizes, then choose larger. Hopefully you’ve had some experience with buying gloves and can choose based upon the fit of a previous pair. If you have no previous experience with glove sizing, go here for help.

Our Two Cents

The Crater Windstopper glove is made for cooler weather and maybe damp weather too. They give a comfy feel without the bulk.

The back of the hand of this glove is Gore Windstopper material. This material stops the wind (you probably figured that out) and is water resistant. It isn’t a waterproof glove however. This glove will be for those that occasionally ride in wet or misty weather. I can picture this glove being great for fall and spring in the Northwest US or along the northwestern coast where it is often foggy and cool.

This glove has a similar feature list with the Hydra H2O, but where the Hydra is waterproof with a light layer of insulation (for colder and/or rainy weather). It all depends on your climate at to which one will suit you better. The glove is textile material on the back of the hand and leather on the palm side. The molded knuckle protector is very substantial, but well shaped and padded on the underside so they feel good on the hand. The palm gets some light padding in the heel area. Goat leather is used in the palm. Both gloves have a soft “wiper” type material along side the index finger you can use to wipe off your visor.

The cuff is a tight knit cuff made to go UNDER your jacket sleeve. These work great with most city or street jacket, but they don’t work so great with race jacket sleeves that zip down close to your wrist. But other than that type jacket, these should work fine. The knit cuff will also keep out the wind. The gloves have a Velcro strap at the wrist to keep the gloves in place in case of a fall.

The gloat leather on the pair I tried on was SO soft and flexible… they are very comfortable! The overall price is really good for a high quality glove like this. :: Paul, 08-24-18

REVIT says: The Crater WSP gloves are equipped with WINDSTOPPER® to prevent wind chill while riding at speed. The short-cuffed gloves are ideal for urban use on colder days, armed with a hard-shell knuckle protector and a Temperfoam® palm slider and PWR | shield at the palm to cope with impact. The Polar fleece liner adds warmth and comfort to the glove. Thanks to the connect fingertip the rider can easily operate any touch-screen device without removing a glove.

Reviews